Plastic Film Crusher Machine:
This machine is suitable for crushing film and sheet, the machine support is made of strong welding steel, the crushing chamber has two parts with hydraulic device, it is easy to open the cover. The inside blade is made of D2 material, and “V” type construction. The hole size of screen can be designed according to customer’s requirement. The bearing is installed outside of the crusher to avoid the dust, it prolong the life of service.
Plastic Film Crusher Technical Parameters:
Model | Feeding size | Motor power | Rotating diameter | Qty of rotating knives | Qty of fixed knives | Mesh size | Rotating speed |
2660 | 634×437 | 15 | φ260 | 3×2 | 2×2 | φ8 | 584 |
3260 | 634×475 | 15 | φ320 | 3×2 | 2×2 | φ12 | 444 |
3280 | 834×475 | 22 | φ320 | 3×2 | 2×2 | φ12 | 627 |
4280 | 834×540 | 37 | φ420 | 3×2 | 2×2 | φ12 | 466 |
42100 | 1034×540 | 45 | φ420 | 3×2 | 2×2 | φ12 | 466 |
42120 | 1234×425 | 55 | φ420 | 3×2 | 2×2 | φ12 | 462 |
52100 | 1034×705 | 55 | φ520 | 5×2 | 2×2/2×3 | φ12 | 462 |
52120 | 1234×705 | 75 | φ520 | 5×2 | 2×2/2×3 | φ12 | 462 |
66120 | 1234×1080 | 90 | φ660 | 5×2 | 2×2/2×3 | φ12 | 462 |
66160 | 1634×1080 | 132 | φ660 | 5×2 | 4×2/4×3 | φ12 | 414 |
80160 | 1634×1000 | 160 | φ800 | 5×2 | 4×2/4×3 | φ12 | 414 |
80200 | 2034×1000 | 200 | φ800 | 5×2 | 4×2/4×3 | φ12 | 420 |
80240 | 2034×1000 | 250 | φ800 | 5×2 | 4×2/4×3 | φ12 | 415 |
Operation Process of Recycled Plastic Crusher
Notes in the operation of plastic crusher:
Plastic crusher is used for crushing waste plastics and factory plastic corner materials. Plastic crusher is widely used in recycling of waste plastics and recycling of corner materials in factories.
1. After start-up, if the crusher makes abnormal knocking sound, it should stop running and restart after identifying and eliminating the disadvantages.
2. The crusher must start without load. The feeding equipment can be opened only after the isokinetic rotation is normal. The feeding material should be gradually increased until full load.
3. To feed evenly, raw materials should not be crowded with crushing chamber; the maximum size of feeding material should not be greater than 0.85 times the width of feeding hopper; at the same time, non-crushing materials should be prevented from entering crusher when feeding; once these non-crushing materials are found to pass through the discharge port, belt transportation should be notified immediately to stop in time so as not to cause serious equipment accidents when entering the next crusher.
4. During operation, regular checks should be taken to observe the condition of various parts of the crusher and bearing temperature by means of watching, listening and touching. Bearing temperature should not exceed 60 C. When the bearing temperature is found to be too high, stop immediately. Oil volume should be increased, forced ventilation and water cooling should be adopted. After the bearing temperature drops, stop and check and troubleshoot.